RGB MCU Display Pattern Dual Channel 24 LED VU Level Indicator Meter F Amplifier

Description

Descriptions:
100%Brand New and High Quality
Youtube Vedio: youtube.com/watch?v=dzaOOp0jLTU,
Thanks for my Kind customer making!
Introduction: This three color SMD LED, colorful, color flexible configuration, prefabricated a variety of color scheme, can set a color scheme specific to the color of each point, there are various design can choose, can adjust the brightness, the sensitivity adjustable, can set the infrared remote control self learning convenient control, infrared remote control need to match, only supports theN/E/C, this format is more common, can take home try television, set-top boxes, I get home in nine receiver remote control, remote control, haier TV Tmall magic box remote control and a waste of VCD remote control test can be used, remote control of home electric fans and air conditioning remote control test can’t use).
Size: length: 100 mm width :35 mm thickness :12.5 mm installed two hole center distance : 52 mm ,hole diameter: 3.2 mm (installation note mounting holes around the wiring insulation plus insulation gasket)
Power supply: DC5v -6 v / 250 mA(Maximum current is LED the whole amount and the highest brightness, generally less than 100 mA)
Audio signal: pick up the three lines on the headphone jack, respectively is a signal Ground (together with the power of the board negative) )left sound channel, right channel.
Functional status and buttons operation: K1 and K2 two buttons, press is have short press and long press .
The following statement didn’t explain the long press is said short press
1, level display status: according to the last time after the power supply power, the brightness of the former, figure, color scheme and sensitivity to normal level.
This state the button function: K1 / show pattern selection click in a pattern, pattern at the end of the cycle from the very beginning.
K1 long press/to enter the pattern of color scheme selection state (note: the bottom upward emission pattern buttons on long press to enter the infrared learning state).
K2 / sensitivity select click change sensitivity level, the order is the highest sensitivity…..The lowest sensitivity > > sensitivity automatically return to the highest sensitivity.
K2 long press/entered into a state of brightness adjustment.
2, Brightness adjustment status: the left section 24 of the bright display 8 red 8 green 8 blue, on the right shows the current brightness (red), 3 pieces according to grade 1, Toatl grade 8.
This state the button functions: K1 / click the higher brightness level, the highest is all bright.
K1 long press/return level the brightness of the display status and return before entering the set.
K2 / brightness click on the lower level, the lowest level is the low end of the three led light.
K2 long press/save the brightness of the set and returns the level display status.
3, color scheme selection state: left and right sides of each led all bright led displays the current color keep on top of the mode leds (peak said the color of the peak point).
This state the button functions: K1 / click the show next prefabricated color configuration scheme, the order is a scheme > > the current program, the last a prefabricated scheme > custom solutions (note that custom solutions when the factory is empty, that is, all black, the need to define the color of each dot) > prefabricated plan 1, so cycle.
K1 long press/to save and select the current scheme return level display state.
K2 / press with K1 instead choose order.
K2 long press/to enter a custom color configuration status.
4, custom color configuration status: left and right side shows a custom color (not after custom shows full red) keep on top of the mode leds (peak said the color of the peak point) on the left side of the low end of the led flashing said the current led is selected.
This state the button functions: K1 / click on the selected led moving up , the top the most low-end will move to another column.
K1 long press/color change to the next, change order red, yellow, green, blue, blue, magenta, six colors cycle show.
K2 / click on the selected led moves down a, the bottom will be moved to another column led one of the most high-end.
K2 long according to save the current color scheme and returns a color scheme selection state.
5, infrared learning key state: enter the state of all lights all out K1 and K2 button press any returns level display status
Need N/E/C of the infrared remote control (the remote control need since with) general TV set-top boxes, such as remote control can try sure no air conditioning, remote control or a lot of N/E/C format, is actually use the four buttons on the remote control to the corresponding board K1 short press and press K2 short press and long according to the four functions.
Since the learning process: the first is the K1 short according to the corresponding function, with the remote control of the sensor of the board (without getting too close to) press the button, if learn to work on the left will light up six led and into the K1 long according to the corresponding function learning state again press the corresponding K1 long press the remote control button again to add 6 led into the same process in order to learn the K2 short press and K2 long press after the four keys will automatically save and return to the level display status at that time you can use the remote control to control, convenient try?
If press buttons have no reaction, estimation is infrared remote control code format is not suitable for, can only change the remote control to try again.
TiP:Before ship we will package well,But if found LED light Transportation broken ,please contact us first! thank you!
Packaging
1pcs*5V RGB MCU Adjustable Display Pattern Dual Channel Dual 24 LED level indicator
Payment
Payment
Payable To
Note
PayPal
Paypal
All payments are due within 7 days of the close of auction. Failing to do so, non-paying bidders will be reported to eBay.
Shipping Policy
Delivery Time
We ship to worldwide, it usually takes 10-30 Business Days to delivery.
Shipping address
We ship to your PayPal address. Please, make sure to provide us with correct, precise, and detailed shipping Address.
Send Time
Items will be shipped within 1 to 3 business days upon payment received or cleared.
Note
If you don’t receive items over 30 business days, please notify us via eBay message.
Return Policy
We appreciate your business and offer an instant 7 days return policy.(7 days after receive the item). The returned item has to be in its original condition. We are able to refund your money without shipping cost.
Contact us
For anything about product, price, shipping or order status, please contact us via eBay message.
We love positive feedback and 5 scores DSR. We will leave it for everyone that leaves it for us.